News

Sawdust pellet machine, also called biomass pellet machine, is a complete set of mechanized production equipment that uses solid waste agricultural products and other organic biomass materials as raw materials by pulverizing, pressurizing and densifying and forming plant straw carbon. The pellet machine adopts the extrusion molding method, the interaction principle between the pressing force between the press rolls and the frictional force of the die hole, so that the material is shaped. Material does not need to add any binder or other material during processing. The plant straw granule forming machine uses various crop stalks, tree branches and leaves and other related materials in agricultural production activities, sawdust slags, and waste cultivars grown from fungi as raw materials. The volume of the molded plant straw carbon block is only 1/30 of that of the original plant straw; the specific gravity is 10-15 times that of the same weight of the plant straw; the combustion resistance and calorific value can reach 3500-5500 kcal; moreover, And it is convenient for storage and transportation in daily production activities. Feed pellet machine, sawdust pellet machine, look for Yuguan in Jinan, Shandong. Biomass pellet fuels have a lot more than coal resources: 1. Biomass fuel has low water content and large heat output. Moreover, biomass pellets are free from sulfur phosphorus and non-corrosive, which can extend the service life of the boiler. 2. Straw ash after combustion of biomass fuel is a high quality potassium fertilizer, which can be recycled back to farmland and promote the growth and development of crops. 3. The biomass fuel is of high purity and does not contain gangue or other debris. Wood pellet fuel can replace the burning of wood, traditional coal energy and natural gas to a certain extent, and it is widely used. It is used for coal stoves used in the production of domestic heating stoves, industrial boilers, and alternative power plants. Plant straw granules are a new type of renewable biomass energy, environmentally friendly and clean, and the price is far lower than the market price of coal. The application range is extremely wide. The biomass pellets manufactured by the wood pellets machine have solved many problems in the industry because of the large amount of coal combustion fumes and do not meet the requirements of environmental protection. It is currently the most cost-effective renewable environmental energy source.

Rotexmaster recently spent a million RMB CNC single-column processing lathe officially put into use. This set of equipment is mainly used to process the core components such as the pellet machine main shaft and the bearing chamber to ensure that the concentricity of the bearing parts is within 0.005. The use of this set of equipment has enabled Rotex to improve the quality of the pellet machine equipment and bring customers a satisfactory product.

What are the problems encountered by wood pellet machine during use? Rotex Machinery will answer your questions: 1 After the wood pellet machine is energized, the motor cannot turn, but there is no abnormal noise, no odor and smoke. the reason (1). Power is not on (at least two phases are not open); (2). Fuse blown (at least two phases blown); (3). Control equipment wiring error; (4). The motor has been damaged. Approach (1). Check the power circuit switch, if there is a break point at the fuse or junction box, repair; (2). Check fuse type, cause of fuse, replace fuse (3). Check motor, repair. 2 After the wood pellet machine is energized, the motor does not turn and the fuse blows. the reason (1). One phase power supply is missing, or the stator coils are connected in reverse; (2). Short circuit between stator windings; (3). Stator winding grounding; (4). Stator winding wiring error; (5). The cross section of the fuse is too small; (6). Shorted or grounded power cord. Approach (1). Check if there is a phase of the knife gate is not well, or there is a phase disconnection of the power supply circuit; eliminate the reverse connection failure; (2). Investigate the short circuit point and repair it; (3). Eliminate grounding; (4). Detect misconnections and correct them; (5). Replace fuses; (6). Eliminate the grounding point. 3 After the wood pellet machine is energized, the motor does not turn and there is a buzzing sound. the reason (1). The stator and rotor windings are open circuited (one-phase breakage) or the power supply loses power; (2). The beginning and end of the winding lead wire are connected wrongly or the winding internal connection is reversed; (3). The power circuit contact is loose and the contact resistance is large; (4). Motor load is too large or the rotor is stuck; (5). The power supply voltage is too low; (6). The assembly of the small motor is too tight or the grease in the bearing is too hard and the bearing is stuck. Approach (1). Identify breakpoints and fix them; (2). Check the winding polarity; determine whether the winding head is correct; (3). Tighten the loose wiring bolts and use a multimeter to determine whether the connectors are falsely connected and repair them. (4). Reduce loads or detect and eliminate mechanical failures; (5). Check whether the specified connection method is incorrectly connected to the Y connection method; whether the voltage drop is too large due to the power supply wire being too thin, be corrected; (6). Reassembly makes it flexible; replaces qualified grease and repairs bearings. wood pellets motor start is difficult, with rated load, the motor speed is less than the rated speed. the reason (1). The power supply voltage is too low; (2) Connection method is incorrectly connected to Y connection method; (3) Cage rotors open or broken; (4). Stator and rotor local coils are miswired and reversed; (5). Motor overload. Approach (1). Measure the power supply voltage and try to improve; (2). Correct connection (3). Check open welds and breakpoints and repair; (4). Find out the misunderstanding and correct it. (5). Reducing load. 5 wood chip machine motor no-load current imbalance, three phase difference. the reason (1). Winding end and end of the wrong connection; (2). Power supply voltage imbalance; (3). Windings have faults such as short circuits in the turns and reversed coils. Approach (1) Check and correct; (2) Measure the power supply voltage and try to eliminate the imbalance; (3) Eliminate winding failures. 6 The motor no-load current balance, but the value is large. the reason (1). The power supply voltage is too high; (2) Connected to the motor is incorrectly connected as △; (3) Air gap is too large or uneven. Approach (1). Check the power supply and try to restore the rated voltage; (2). Change to Y connection. (3). Replace new rotor or adjust air gap. Understand that so much can be said to be a great benefit for future operations. Shandong Rotex Machinery Co.,Ltd. wood pellet machine provides high-quality after-sales service for each particle machine purchase user, and always insists on free maintenance service for each product shipped from the factory within one year. , The whole machine warranty (without wearing parts of the pressure roller) within one year. Welcome to visit!

Now more and more pellet machine manufacturers, customer choice is also more and more difficult. As far as Shandong is concerned, from the first few companies to more than a dozen now, the market is gradually showing fierce competition. With the gradual expansion of the development space of the pellets industry, many pellet machine manufacturers have spotted this prospect. Have entered the pellet machine industry. Faced with such a dazzling array of pellet machine manufacturers, customers are sure to find several companies that they are satisfied with on the Internet when they are planning to purchase equipment. The best quality equipment can be purchased at the lowest price. I believe we all know the truth that "shopping is not fooled". But in the process of comparison, it will be found that the appearance of each manufacturer's equipment is not the same, the model is also different, so that the customer is more confused, do not know which product to choose the best. Here to tell you, my company pay attention to the development of pellet machines for many years, there are wood pellets, straw pellets, feed pellets and other machines. The R&D department has been revising and upgrading the equipment according to the feedback from the sales department to better meet the needs of our customers. Since its inception, the company has been adhering to the fine ideas of excellence and has always been committed to meeting the needs of customers and advancing the technological advancement of the industry. On the basis of in-depth digestion and absorption of advanced domestic and foreign advanced products, we have achieved excellent results in the market. The sales of various equipments of the company continued to increase for six consecutive years, and it has obtained CE certification, ISO9001-2008 international system certification and more than ten design patents. Honor witness strength, strength witnessed brilliant. This is the footprint we left on the road of continuous growth. Past brilliance, we cherish our treasures, we will carry honors and move into the future.